insulating concrete forms (ICF), the industry is rampant with false information. Some have gone together industry members, while others are simple misunderstandings about the technology. Most of these misstatements are people who simply lack the proper knowledge behind the information. The hardest part is finding the ICFs of research information, but sorting through all the inaccurate information.
almost every aspect of the ICF industry affected misstated information, but the most common issues include discussions about the R-value insulation, and termite and bugs. R-value of statements ranging from R-18 R-50 +. To explode this myth and get a clearer understanding of this myth, you will need a solid understanding of the R-value and the difference between performance and true R-value.
Myth 1: R-value
R-value is a measure of resistance (R) heat flow. Heat flow may be reluctant to insulating materials such as plastic foam or mineral fiber, or may be slowed down massive dense materials such as thick walls or concrete. higher R-value, the more resistance and better insulation values.
All the building material of heat transfer to a certain extent. Heat transfer can be measured by any of the following: 1 Conductivity (k); 2 Conductivity (c), 3 Transmittance (U); 4 Resistance (R ).
The ability of dense material that slows the flow of heat depends on their ability to store heat and measure the specific heat and heat capacity. (BTU per pounds per degree C, density pounds per cu.ft.; heat capacity BTU per cu.ft. per degree F)
When it comes to the stated R-value in residential construction, insulation values that are applied to the wall or ceiling, usually related to the R-value of insulation material is installed, and not on the wall or ceiling assembly. For instance, when the 2x4 stud wall is insulated with R-11 insulation batt type, the builder stated that the wall is R-11. It's not entirely true and not true, because about 20% of the wall is not insulated at all. wood framing and sheathing have no R-value, but because of isolation due, they add very little. true R-value or performance of R-value within the R-3 and R-9. Add to that the fact that the wall is full penetration, such as electrical outlets, etc. and the fact that the wall itself is actually hollow in nature. This added a thought leads to another discussion of air leakage through the wall.
with ICF technology, TRUE value of the insulation wall is that of expanded polystyrene (EPS) EPS from continuing providing insulation from the ground plane to the top plate. insulation value of EPS is determined density and thickness of the material. Some systems have ICF EPS, which is of different thickness (waffle and post and beam system) which is usually an average thickness of the foam. It is, in my opinion, is not an accurate measurement because the bucket with a hole in the bottom do not carry as much water as a solid bucket with a hole at the top. Most ICFs used EPS foam has a density of about 1.5 pounds PCF PCF to 2.0 pounds. insulation values differ only slightly in that range, depending on testing laboratory, providing R-values ranging from R-4 and R-4, 5 per inch of thickness of EPS.
argue that the ICF walls are R-50 began several years ago after the insulating concrete form Association (ICFA) and several members ordered CTL Laboratories in Chicago for performing an R-value testing and analysis. summary report basically said that, depending on climate zone, PERFORMANCE R-values for ICF technology is as high as R-52 as compared to typical wood frame construction and batt. To make accurate comparisons, it must be ensured that the comparison is made in relation to ICF an alternative to the project. On average, the performance of R-value is much less than the claimed R-50. A study by the consumer must be done to clarify the comparison of the actual project. In short, ICF will perform at R-50, but this statement is correct as far as insulation value goes.
argue that the ICF walls are R-50 began several years ago after the insulating concrete form Association (ICFA) and several members ordered CTL Laboratories in Chicago for performing an R-value testing and analysis. summary report basically said that, depending on climate zone, PERFORMANCE R-values for ICF technology is as high as R-52 as compared to typical wood frame construction and batt. To make accurate comparisons, it must be ensured that the comparison is made in relation to ICF an alternative to the project. On average, the performance of R-value is much less than the claimed R-50. A study by the consumer must be done to clarify the comparison of the actual project. In short, ICF will perform at R-50, but this statement is correct as far as insulation value goes.
...Myth 2: Waterproofing
Yes, below the concrete structure should always be watertight, and that includes ICF technology. Three options include: dimpled membrane, peel and stick membrane, and roll-on/spray-on products. In some states in the U.S., the combination of dimpled membrane and peel and stick membrane or roll-on/spray-on products must be used to meet local building codes. It is best to contact the local building code officials and your local ICF suppliers to ensure that they meet the minimum requirements of code and only use products that are compatible with EPS.
Myth 3: Termites and Bugs
According to ICFA, the International Residential Code has a provision in the IRC to allow the foam to be used below grade. IRC provides in addition to chemical treatment of soil, foam can be used below grade on the outside wall, if one of the following conditions is met:
Remember, these insects do not eat the foam, but they can burrow through it, especially in search of food. Eliminate the food source and eliminate the problem. Wood products can be completely replaced in their new home. No more reasons to use wood products in the areas of the U.S. with high termite infestation. Think about steel framing, Azekah Trimboards and V-Buck for your next project and get the wood! Although there are many additional myths continue to thrive, it is important to remain diligent in collecting information. As you seek additional information, be sure to work with those who have a heart for teachers. Looking for those who have a passion for the industry, and both understand and can explain the issues.
Tidak ada komentar:
Posting Komentar